Replacement UPVC Door Handles
Find the perfect handle for your door, whether you're replacing your handles or adding additional security. These upvc handle are easy to install and have the required 92mm central distance for multipoint locks.
The most important measurements to consider are backplate fixing centres and lever/key hole dimensions. Compare these measurements carefully with your current measurements prior to ordering.
Lever/Pad
Lever pad door handles are made up of a lever handle on one side and a paddle shaped handle on the other. They are designed to work with key wind locks, however they can also be fitted to multipoint split spindle door locks (though you'll need a separate dual spindle lock case).
Once you have chosen the right handle for your doors, the finishes will be listed in the drop-down list. Certain styles of handles are not available in all finishes. It is recommended to examine the technical drawing and dimensions sections for the particular item that you want to ensure you get the right size and fit.
When choosing new lever pad door handles made of Upvc it is important to ensure that they correspond to the PZ (distance between the spindle of the handle and the center of the cylinder hole) of your existing multipoint locks, as they need to be in the same line to allow doors to remain locked, whether from the inside or outside. The handles we offer are designed to work with a variety of conventional cylinder locks, however you should always double-check before ordering.
If you are looking to upgrade to dual spindle levers you'll need to remove the handles you have already installed and take apart the lock case. This will require an additional split inline cylinder. They can be purchased separately and we have an entire technical diagram for you to take a look at in the pictures for each product.
It is a good idea to loosen the screws that are holding your existing door handle and then examine the mechanism. If the screws are too tight, you may need to loosen them even more. Then, you can remove the spindle from the handle and replace it with your new Upvc handle. Before putting the handle in position, it is recommended to make sure it is in the right position, and you can do this by placing your finger into the gap between the door frame and the door handle to make sure that it is in a level position.
Lever/Lever
Lever door handles function as an a multi-point lock using the Euro Cylinder and can be found on most upvc double doors, aluminium doors, and some wooden doors. They are available in two forms, having an interior lever and a paddle on the outside. Sprung - These have an internal spring cassette within the backplate that helps bring the handle lever into the horizontal position. Non-sprung: These do NOT have a mechanism for bringing the handle lever to a horizontal position.
To fix the door handle of a lever that is sagging you must find the hole for access to the detent or pin, which is typically a small rectangle or round shaped hole or protruding pin that is located on the opposite side of the base plate. Once located you can loosen the set screw using the help of a screwdriver, and then remove it to allow the lever and return it to the horizontal position.
Once the handle is in a horizontal orientation, you can put the screws back in place and tighten them to make sure the handle remains fixed to the base plate. It is also advisable to apply a threadlocking adhesive to the screw threads to improve the grip and stop them from becoming loose over time.
Drooping lever handles on door handles can be caused by many factors. The most common cause is that the fixings are too tight, causing the lever bearing to pull up against the door. browse around this website could also be due to the fact that the levers aren't operated in a straight line and this is compressing the latch mechanism preventing it from fully springing back into action.
Another common reason is that the sprung lever isn't working properly. This is typically due to the spring not being in the correct position within the backplate. The most effective way to determine this is to operate the handle and see whether it changes to its horizontal position.
It is crucial to fix any loose door handles as soon as possible. This could cause excessive wear on the screws, and the handle might be able to fall off the base plate. It is also a good idea to tighten all screws that are loose on a regular basis to help to prevent them from becoming loose.
Lever/Snib
These handles made of upvc are also known as 'Snib' handles and have a snib lever towards the top of the lever that you can push down to lock your door if you don't use the dummy lock. They are typically fitted with a Fullex 68PZ (that's 68mm between the spindle's centre and the lever or lock centre) door lock. We also have a range of other door handles with 68PZ from manufacturers like Ferco and Fab & Fix.
You can upgrade your home by changing your door handles whether you are replacing your existing handles or installing new ones on doors you have built. There are a variety of styles available for door handles made of upvc including the traditional lever on backplate. Other options include straight or curly short latches, as well as dummy knobs for multi-point locks. These are perfect for French doors.
Lever on backplate handles are often rectangular in shape but there are also oval or circular-shaped versions, which are known as rose door handles. These door handles are characterized by a lever or knob that is mounted on a backplate. The backplate is removable for concealed fixing.
These handles are available in a variety of finishes, including chrome and coloured finishes to be matched to your door and hardware such as knobs, hinges, and bolts. Some handles have a grub screw to attach the lever or knob firmly to the spindle. Some handles come with bathroom spindles that can be used for bathroom locks. They also come with a thumbturn release mechanism, and can be used on doors for bathrooms.
Mortise
The tubular latch is the most likely to be the cause if your uPVC door handle is slammed shut. This could be due to many things, but the most common is a lack of lubrication in the latch plate. This can be fixed quite easily by simply opening the door and spraying lubricant onto the lock and handle. Alternatively, it could be that the latch plate is detached from the backplate. This is a more complicated issue that requires a professional.
A multipoint door handle is the ideal solution to solve the issue of a stuck door handle. The handles are positioned through the faceplate and are operated by the use of a key or thumb turn knob which activates the cam that locks the deadbolt. The handles are available in different sizes to fit various kinds of uPVC doors and are available in a variety of attractive finishes that match existing hardware. The handles can be bought on the internet or through the local locksmith and are simple to install, with clear instructions.
You will need to know your PZ size of your cylinder in order to select the right replacement handle set. This is the measurement in millimetres between the inside edge of the door frame and the centre of the hole in the handle. You'll also need the type of lock that is installed on your door, whether it is a mortise or hook lock. Once you know these measurements, the most efficient way to find the correct handles is to use the filter by brand on the website. This will help you narrow down your options, and then you can select the correct size.
A typical set of handles includes the handle and a pair of different length screws as well as drill guides and installation instructions. The smarter models, such as the Igloohome Smart Mortise 2+ includes a complete mortice lock with a built-in keypad. These are more complicated units that are best designed for professional installers or highly skilled DIYers. Certain handle sets come with an array of other accessories, like weather strips that can be used to enhance the look of the door.